- Digital multimeter measures AC/DC voltage, AC/DC current, resistance, capacitance, frequency, and temperature.
- Manual and auto ranging modes for user flexibility. RPM measurements with inductive pickup.
- Built in thermometer allows for temperature readings without a separate instrument.
- Performs millisecond pulse width measurements for fuel injectors. Millisecond pulse width measurements for fuel injectors.
- Safety rated for Category III to 1000V and Category IV to 600V. Resistance, continuity and diode test.
- Resistance, continuity and diode test.
- RPM measurements with inductive pickup.
- Millisecond pulse width measurements for fuel injectors.
Product Description
-------------------
The Fluke 88 V/A KIT Automotive Multimeter Combo Kit comes with
the 88 Series V automotive multimeter, silicone test leads,
alligator clips, test probes, inductive RPM pick-up probe,
ToolPak magnetic meter hanging kit, temperature probe, two
automotive backprobe pins, insulation piercing probe, and a
durable carrying case. The digital multimeter (also known as a
multitester) is designed for use in high energy environments such
as those found on hybrid vehicles and measures AC/DC voltage up
to 1,000V, AC/DC current to 10 amp (20 amp for a maximum of 30
seconds), frequency to 200 kilohertz, resistance to 50 megaohms,
capacitance to 9,999 microfarads, temperature from -200 to +1090
degrees C (-328 to +1994 degrees F) and includes continuity and
diode tests. The 6,000-count resolution, 3-3/4 digit digital
display has a bright white backlight for readability in low-light
conditions with a 4-1/2 digit mode for precise measurements and
displays an analog bar graph which is useful for fast-changing or
unstable signals. The meter performs millisecond pulse width
measurements for fuel injectors and has Min./Max.-Average
as well as a Min./Max. Alert to automatically capture
variations. A duty cycle indicates the percentage of time a
signal is above or below the trigger level during one cycle and a
peak capture function detects intermittent problems and
transients as low as 250 microseconds. The meter has both manual-
and auto-ranging modes for user flexibility, and an auto-hold
function to capture stable readings. The relative mode removes
test lead resistance from low ohms measurements. This meter is
safety rated for Category III up to 1000V and Category IV up to
600V and can withstand hazardous volt spikes in excess of 8,000V
to reduce risks of spikes and surges caused by load sw and
faults on industrial circuits. It uses a 9V battery (installed)
that has a battery life of approximately 400 hours without
backlight and has a selectable mode to maximize battery
life. The meter measures 20.1 x 9.8 x 5.2 cm (H x W x D) and
weighs 22 oz. (624 g). (H is height, the vertical distance from
the lowest to highest point; W is width, the horizontal distance
from left to right; D is depth, the horizontal distance from
front to back.)
The ToolPack Hanging Kit includes a universal hanger, magnet, and
17" (23 cm) hanger strap for hands-free operation. SureGrip
alligator clips are insulated and nickel-plated for gripping
objects up to 3/8" (9.5mm). SureGrip silicone test leads have 1.5
m (4.9') silicone-insulated wire to resist heat and cold. All
included SureGrip accessories are rated for Category III up to
1000V and Category IV up to 600V.
Multimeters are electrical test meters that measure multiple
properties of an electrical circuit, such as current, voltage,
resistance, capacitance, and continuity. Available in handheld or
benchtop models, multimeters diagnose electrical problems in
electrical equipment, wiring, and power supplies. A variety of
probes, clamps, and leads can be used to connect the meter to a
circuit or device. Multimeters display information either in
analog or digital form. Factors that influence meter choice
include the electrical properties to be measured, the anticipated
range of results, and the desired level of protection against
transient voltage. Safety ratings are based on International
Electrotechnical Commission (IEC) standards for low-voltage test
equipment. IEC 61010 delineates four overvoltage installation
categories. In general, a meter with a category IV rating will
provide more protection against transient voltages than a meter
with a lower category rating.
Fluke Corporation manufactures electrical testing tools and
software for industrial and commercial applications. The company,
founded in 1948, is headquartered in Everett, WA.
What's in the Box?
------------------
* Model 88V multimeter
* SureGrip silicone test leads
* SureGrip large jaw alligator clip set
* Test probes
* Inductive RPM pick-up probe
* ToolPak magnetic meter hanging kit: universal hanger; magnet;
17" (23 cm) hanging strap
* Temperature probe
* (2) automotive backprobe pins
* Insulation piercing probe
* Durable carrying case
* Holster
* 9V battery (installed)
* Instructions
* Instructional CD
From the Manufacturer
---------------------
A complete automotive diagnostic package. Improved measurement
functions, trouble-shooting features and accuracy to solve more
problems on conventional and hybrid vehicles. Built-in
thermometer lets you carry one less tool (temperature probe
included). Resistance, continuity and diode test. RPM
measurements with inductive pickup (included). Millisecond pulse
width measurements for fuel injectors. Frequency to 200 kHz and %
duty cycle. Measure up to 1000 V ac and dc. Measure up to 10 A,
20 A for up to 30 seconds. 4_digits for precise measurements.
Features: Magnetic hanger to attach meter to the vehicle and free
your hands for other tasks. Min/Max-Average with
Min/Max Alert to capture variations automatically. Relative mode
to remove test lead interference from low ohms measurements.
Large display digits and two-level bright white backlight for
increased visibility. Analog bargraph for fast changing or
unstable signals. Access door for fast battery changes without
opening up the case. Limited lifetime warrantee, UL and CSA
approved. Made in USA. 88V/A Combo Kit includes: 88V Automotive
Multimeter. 1.5m long heat resistant silicone test leads.
Removable test probes to pierce corroded terminals. Alligator
clips.. Magnetic hanger to position and hold meter to steel
surfaces. Temperature probe. Inductive RPM pick-up probe. Two
back probe pins. Insulation piercing clip (red). Durable case.